Line Magnetic – Read This Article..

DIY Speaker Cables are a great way to improve your home theater or audiophile setup without blowing wads of money. The big brands would like you to believe that their cables are made with some secret ingredient, guess what, there not. With a few simple tools, some affordable parts, and a little know how you can create Cayin Audio that not only rival the sound quality of the big brands, nevertheless the appearance too. Simply adhere to the steps below.

Step 1: Gather the Tools and Parts – You will need to collect these tools: a tape measure, a spool of yarn or string, a ruler, scissors, a little screwdriver or screwdriver set, an exacto knife or box cutter. After you have gathered your tools you will have to purchase the parts needed to build the speaker cable. The various components include: your required period of speaker wire 10-20% extra, the required period of sleeving 10-20% extra, your preferred end connectors, cable pants which can be the correct size for your cable. Additionally you will want two sizes of heat shrink, along with a roll of scotch tape.

Step Two: Measure and Cut – In case you are not sure what length cable you will need, run some strong from your stereo to your speaker following the route you plan to run the speaker cable. Give a foot or two depending on the overall length, and then measure the duration of the string.

Once you measure out your length cut your speaker cable towards the length you may have calculated. Now measure the size of one cable pant, and inside entire connector (for instance in a banana plug the duration of the cable that will be within the banana plug).

Consider the number and double it. Now cut your sleeving in a entire speaker cable minus the calculation through the pants and banana plug. Add an inch to be safe.

Step Three: Slide on the Sleeving – Now that you have most of your components measured out, it is time to slide on the sleeving. In the event you used the chart from step 2 you should have no worries getting it on the cable. Make use of a slinky like motion to push the sleeving within the cable.

Slide about 4 or 5 inches at the same time, give it time to bunch up and then push the bunch further along the cable. For Audiophile Cables this could take the time, show patience and just keep repeating the slinky motion. If you want to you can apply some scotch tape for the ends of the speaker cable in a cone like shape, this will help the cable slide with the sleeving without getting snagged.

Step 4: Apply the temperature Shrink – Now that you have the sleeving on you could have noticed the ends are starting to fray, no reason to worry. Take your heat shrink (At the end of the article you will find size recommendations) and stop two half inch long pieces. You won’t be seeing this heat shrink ultimately, so don’t fret whether its not exactly half of an inch long, or if perhaps its not cut perfectly straight.

Take the heat shrink and slide it over the end of the sleeving, in the event the sleeving is just too frayed use a bit of scotch tape to temporarily hold along the fray, simply wrap the tape round the end in the sleeving, slide the heat shrink on the tape and take off the scotch tape.

Don’t leave the tape as the next step might make it burn.

Once the heats hrink is positioned to protect the fraying ends in the sleeving, make use of a lighter, heat gun or hairdryer to shrink the temperature shrink. Take care not to burn the warmth shrink or perhaps the sleeving around it.

Step 5: Slide on the Cable Pants – The heat shrink you applied in step 5 should alllow for an even setting up the speaker pants. Measure the length of the speaker cable from your end in the heat shrink towards the end in the cable. It should be the size of the cable pants the useable period of your connector a little bit more. Take scissors or perhaps an Exacto knife and create a circular cut across the speaker cable sheath. Eliminate the sheath and stop any cotton fiber that could have been utilized in the cable construction. You will now slide on the cable pants. In the event the individual legs in the pants have a problem sliding within the speaker cable conductors, apply a tiny amount of dish soap for the speaker cable to aid in this process.

After the cable pants are saved to you should slide them as far down as they can go, and then support about 1/4″. This will provide you with some room for error over the following step.

Step 6: Install the Connector – Using the sleeving, heat shrink and cable pants already on your cable you happen to be almost done. The final step is to use your selection of connector. You can choose from banana plugs, spades or pins. No matter what connector you choose, the steps are the same. Depending on your connector you may need to slide the decorative cover on the cable pants before the following steps.

Unscrew the set screws. Slide the speaker cable with all the covering still on in to the connector. Mark the cable as near the connector as you can. Utilizing the mark manufactured in step three strip the sheath off the individual conductor. Slide off of the protective sheath, then slide the bare wire back into the connector. (Do not touch the bare wire with your bare fingers since the qzuqtl will not assist the copper).

Tighten the set screws completely making sure they line up on the bare wire. According to your connector setup, screw on the decorative cover. For the correct size components please reference the subsequent chart: DIY Speaker Cable Component Size There is not any limit towards the creativity you can utilize when creating you cables. You could add some heat shrink over the surface of the joint involving the Line Magnetic, or use colored heat shrink to mark each conductor.

For additional color you can utilize multiple layers of sleeving, such as metallic or glow-in-the-dark-clear over top of one of your liking. Finally ViaBlue makes great cable splitters which you can use instead of cable pants for additional style.